Araştırma Makalesi
BibTex RIS Kaynak Göster

Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy

Yıl 2023, Cilt: 7 Sayı: 2, 70 - 81, 20.06.2023

Mehmet Şükrü Adin

https://doi.org/10.26701/ems.1270937
Cited By: 26

Öz

The quality of drilled holes in aluminium alloys used in the aerospace industry is vital to ensure high-precision structural integrity. For this reason, optimum selection of cost-effective cutting tools and cutting parameters is of great importance. Nowadays, due to their high cost and supply difficulties, there is a great interest in improving the performance of traditional HSS cutting tools as an alternative to ceramic, carbide and coated cutting tools. HSS cutting tools are widely used in different industries due to their cost-effectiveness and suitability to improve tool performance. In this research, the performances of cryo-treated (DC&T) and untreated (UT) HSS cutting tools used in dry machining of AA7075 aluminium alloys were investigated. Thanks to DC&T processes applied to HSS cutting tool, improvements have occurred in its microstructure. The hardness value of HSS cutting tool increased by 6.89% with the effect of DC&T processes applied. When the highest and lowest Ra values obtained using DC&T and UT HSS cutting tools were compared, it was seen that DC&T HSS cutting tool performed better by 11.05% and 25.91%, respectively. It has been determined that the hole surface quality of the aluminium workpiece machined with DC&T and UT HSS drills is negatively affected by the increase in spindle speed and feed rate. The highest S/N ratios calculated according to Ra values of holes drilled on aluminium workpieces using DC&T and UT HSS cutting tools were found to be -7.12 dB (2.27 μm) and -9.62 dB (3.03 μm), respectively. In the ANOVA analysis, it was determined that the most effective parameters on Ra values were spindle speed (70.62%), tools (18.19%) and feed rate (9.98%), respectively. In the regression analysis, R2 value for Ra values was calculated as 98.30%. High R2 value result shows that the model developed is quite successful in estimating Ra values.

Anahtar Kelimeler

AA7075 Aerospace alloys Aluminium Cryogenic treatment HSS cutting tools Machining Surface roughness

Kaynakça

  • [1] Aamir, M., Giasin, K., Tolouei-Rad, M., Vafadar, A., (2020). A review: Drilling performance and hole quality of aluminium alloys for aerospace applications. Journal of Materials Research and Technology, 9(6): 12484-12500.
  • [2] Pinar, A.M., (2013). Optimization of process parameters with minimum surface roughness in the pocket machining of AA5083 aluminum alloy via Taguchi method. Arabian Journal for Science and Engineering, 38: 705-714.
  • [3] Campbell, F.C., (2008). Elements of metallurgy and engineering alloys. ASM international, 487-508.
  • [4] Zhao, J., Deng, Y., Tang, J., Zhang, J., (2019). Influence of strain rate on hot deformation behavior and recrystallization behavior under isothermal compression of Al-Zn-Mg-Cu alloy. Journal of Alloys and Compounds, 809: 151788.
  • [5] Sun, D. et al., (2018). Hole-making processes and their impacts on the microstructure and fatigue response of aircraft alloys. The International Journal of Advanced Manufacturing Technology, 94(5): 1719-1726.
  • [6] Zhu, Z. et al., (2018). Evaluation of novel tool geometries in dry drilling aluminium 2024-T351/titanium Ti6Al4V stack. Journal of Materials Processing Technology, 259: 270-281.
  • [7] Kalidas, S., DeVor, R.E., Kapoor, S.G., (2001). Experimental investigation of the effect of drill coatings on hole quality under dry and wet drilling conditions. Surface and Coatings Technology, 148(2-3): 117-128.
  • [8] Aamir, M., Tolouei-Rad, M., Giasin, K., Vafadar, A., (2020). Machinability of Al2024, Al6061, and Al5083 alloys using multi-hole simultaneous drilling approach. Journal of Materials Research and Technology, 9(5): 10991-11002.
  • [9] Jovičević-Klug, P., Puš, G., Jovičević-Klug, M., Žužek, B., Podgornik, B., (2022). Influence of heat treatment parameters on effectiveness of deep cryogenic treatment on properties of high-speed steels. Materials Science and Engineering: A, 829: 142157.
  • [10] Molinari, A., Pellizzari, M., Gialanella, S., Straffelini, G., Stiasny, K., (2001). Effect of deep cryogenic treatment on the mechanical properties of tool steels. Journal of materials processing technology, 118(1-3): 350-355.
  • [11] Da Silva, F.J., Franco, S.D., Machado, A.R., Ezugwu, E.O., Souza Jr, A.M., (2006). Performance of cryogenically treated HSS tools. Wear, 261(5-6): 674-685.
  • [12] Adin, M.Ş., (2022). Kriyojenik ısıl işlem uygulanmış özel tasarlanmış matkap uçları ile fiber takviyeli cam-epoksi kompozitin delme performansı ve mekanik özelliklerinin incelenmesi. Doktora Tezi, Batman Üniversitesi Lisansüstü Eğitim Enstitüsü, 1-266.
  • [13] Jovičević-Klug, P., Jovičević-Klug, M., Podgornik, B., (2020). Effectiveness of deep cryogenic treatment on carbide precipitation. Journal of Materials Research and Technology, 9(6): 13014-13026.
  • [14] Jovičević-Klug, P., Tóth, L., Podgornik, B., (2022). Comparison of K340 Steel Microstructure and Mechanical Properties Using Shallow and Deep Cryogenic Treatment. Coatings, 12(9): 1296.
  • [15] Akhbarizadeh, A., Shafyei, A., Golozar, M., (2009). Effects of cryogenic treatment on wear behavior of D6 tool steel. Materials & Design, 30(8): 3259-3264.
  • [16] Gürbüz, H., Baday, Ş., (2021). Milling Inconel 718 workpiece with cryogenically treated and untreated cutting tools. The International Journal of Advanced Manufacturing Technology, 116: 3135-3148.
  • [17] Baday, Ş., Ersöz, O., (2022). Comparative investigations of cryo-treated and untreated inserts on machinability of AISI 1050 by using response surface methodology, ANOVA and Taguchi design. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 236(3): 1751-1765.
  • [18] Güney, F., Menderes, K., Gerengi, H., Kaya, E., Yıldız, M., (2022). Farklı Bekletme Süreli Derin Kriyojenik İşlemin Sementasyon Çeliğinin Korozyon Davranışına Etkisinin Araştırılması. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 9(2): 703-712.
  • [19] Kam, M., İpekçi, A., Argun, K., (2022). Experimental investigation and optimization of machining parameters of deep cryogenically treated and tempered steels in electrical discharge machining process. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 236(5): 1927-1935.
  • [20] Güney, F., Menderes, K., (2022). AISI 8620 (20NiCrMo2) Çeliğinin Mekanik Özelliklerine Kriyojenik İşlemin Etkisinin İncelenmesi. İmalat Teknolojileri ve Uygulamaları, 3(2): 22-31.
  • [21] Lal, D.M., Renganarayanan, S., Kalanidhi, A., (2001). Cryogenic treatment to augment wear resistance of tool and die steels. Cryogenics, 41(3): 149-155.
  • [22] Akincioğlu, S., Gökkaya, H., Uygur, İ., (2015). A review of cryogenic treatment on cutting tools. The International Journal of Advanced Manufacturing Technology, 78(9-12): 1609-1627.
  • [23] Gill, S.S., (2012). Machining performance of cryogenically treated AISI M2 high speed steel tools. Journal of Engineering Research and Studies, 3(2): 45-49.
  • [24] Shirbhate, A., Deshpande, N., Puri, Y., (2012). Effect of cryogenic treatment on cutting torque and surface finish in drilling operation with AISI M2 high speed steel. Int. J. Mech. Eng. Rob. Res, 1(2): 50-58.
  • [25] Firouzdor, V., Nejati, E., Khomamizadeh, F., (2008). Effect of deep cryogenic treatment on wear resistance and tool life of M2 HSS drill. Journal of materials processing technology, 206(1-3): 467-472.
  • [26] Podgornik, B., Leskovšek, V., Vižintin, J., (2009). Influence of deep-cryogenic treatment on tribological properties of P/M high-speed steel. Materials and Manufacturing Processes, 24(7-8): 734-738.
  • [27] Taguchi, G., (1987). System of experimental design, quality resources, New York, USA.
  • [28] Tiwary, V.K., Arunkumar, P., Malik, V.R., (2023). Investigations on microwave-assisted welding of MEX additive manufactured parts to overcome the bed size limitation. Journal of Advanced Joining Processes, 7: 100141.
  • [29] Tiwary, V.K., Padmakumar, A., Malik, V.R., (2022). Investigations on FSW of nylon micro-particle enhanced 3D printed parts applied to a Clark-Y UAV wing. Welding International, 36(8): 474-488.
  • [30] Tiwary, V.K., Padmakumar, A., Malik, V., (2022). Adhesive bonding of similar/dissimilar three-dimensional printed parts (ABS/PLA) considering joint design, surface treatments, and adhesive types. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 236(16): 8991-9002.
  • [31] Adin, M.Ş., İşcan, B., Baday, Ş., (2022). Optimization of welding parameters of AISI 431 and AISI 1020 joints joined by friction welding using taguchi method. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 9(1): 453-470.
  • [32] Adin, M.Ş., İşcan, B., (2022). Optimization of process parameters of medium carbon steel joints joined by MIG welding using Taguchi method. European Mechanical Science, 6(1): 17-26.
  • [33] Ross, P.J., (1988). Taguchi technique for quality engineering. McGraw-Hill Professional, New York, USA
  • [34] Suthar, J., Teli, S., Murumkar, A., (2021). Drilling process improvement by Taguchi method. Materials Today: Proceedings, 47: 2814-2819.
  • [35] Sarikaya, M. et al., (2021). Cooling techniques to improve the machinability and sustainability of light-weight alloys: A state-of-the-art review. Journal of Manufacturing Processes, 62: 179-201.
  • [36] Markopoulos, A.P., Davim, J.P., (2017). Advanced machining processes: innovative modeling techniques. CRC Press, Taylor & Francis, 1-351.
  • [37] Giasin, K., Hodzic, A., Phadnis, V., Ayvar-Soberanis, S., (2016). Assessment of cutting forces and hole quality in drilling Al2024 aluminium alloy: experimental and finite element study. The International Journal of Advanced Manufacturing Technology, 87(5): 2041-2061.
  • [38] Aamir, M., Tolouei-Rad, M., Giasin, K., Vafadar, A., (2020). Feasibility of tool configuration and the effect of tool material, and tool geometry in multi-hole simultaneous drilling of Al2024. The International Journal of Advanced Manufacturing Technology, 111(3): 861-879.
  • [39] Aamir, M., Tolouei-Rad, M., Giasin, K., (2021). Multi-spindle drilling of Al2024 alloy and the effect of TiAlN and TiSiN-coated carbide drills for productivity improvement. The International Journal of Advanced Manufacturing Technology, 114(9): 3047-3056.
  • [40] Aamir, M., Tolouei-Rad, M., Vafadar, A., Raja, M.N.A., Giasin, K., (2020). Performance analysis of multi-spindle drilling of Al2024 with TiN and TiCN coated drills using experimental and artificial neural networks technique. Applied Sciences, 10(23): 8633.
  • [41] Santos, M.C., Machado, A.R., Sales, W.F., Barrozo, M.A., Ezugwu, E.O., (2016). Machining of aluminum alloys: a review. The International Journal of Advanced Manufacturing Technology, 86: 3067-3080.
  • [42] Ng, E., Szablewski, D., Dumitrescu, M., Elbestawi, M., Sokolowski, J., (2004). High speed face milling of a aluminium silicon alloy casting. CIRP Annals, 53(1): 69-72.
  • [43] Tash, M., Samuel, F., Mucciardi, F., Doty, H., Valtierra, S., (2006). Effect of metallurgical parameters on the machinability of heat-treated 356 and 319 aluminum alloys. Materials Science and Engineering: A, 434(1-2): 207-217.
  • [44] Fuh, K.-H., Wu, C.-F., (1995). A residual-stress model for the milling of aluminum alloy (2014-T6). Journal of Materials Processing Technology, 51(1-4): 87-105.
  • [45] Lahres, M., Müller-Hummel, P., Doerfel, O., (1997). Applicability of different hard coatings in dry milling aluminium alloys. Surface and Coatings Technology, 91(1-2): 116-121.
  • [46] Kurt, M., Bagci, E., Kaynak, Y., (2009). Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. The International Journal of Advanced Manufacturing Technology, 40(5): 458-469.
  • [47] Phadke, M.S., (1995). Quality engineering using robust design. Prentice-Hill, Englewood Cliffs, NJ, USA.
  • [48] Çiçek, A., Kıvak, T., Ekici, E., (2015). Optimization of drilling parameters using Taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills. Journal of Intelligent Manufacturing, 26(2): 295-305.
  • [49] Ross, P.J., (1996). Taguchi techniques for quality engineering: loss function, orthogonal experiments, parameter and tolerance design, 1-279, ‎ McGraw Hill, Boston, USA.
  • [50] Adin, M.Ş., (2022). Lazer kaynağı ile kaynak yapılan alüminyum alaşımlarının mekanik özelliklerinin araştırılması ve kaynak parametrelerinin taguchi ve anova yöntemleri kullanılarak optimizasyonu. Journal of Science, Technology and Engineering Research, 3(2): 50-59.
  • [51] Kumari, S., Bandhu, D., Muchhadiya, A., Abhishek, K., (2023). Recent trends in parametric influence and microstructural analysis of friction stir welding for polymer composites. Advances in Materials and Processing Technologies, 1-21.
  • [52] Murali Mohan, M., Venugopal Goud, E., Deva Kumar, M., Kumar, V., Kumar, M., “Parametric Optimization and Evaluation of Machining Performance for Aluminium-Based Hybrid Composite Using Utility-Taguchi Approach,” in Recent Advances in Smart Manufacturing and Materials: Select Proceedings of ICEM 2020, 2021: Springer, 289-300.
  • [53] Montgomery, D.C., (2017). Design and analysis of experiments, Ninth ed. John wiley & sons.

Yıl 2023, Cilt: 7 Sayı: 2, 70 - 81, 20.06.2023

Mehmet Şükrü Adin

https://doi.org/10.26701/ems.1270937
Cited By: 26

Öz

Kaynakça

  • [1] Aamir, M., Giasin, K., Tolouei-Rad, M., Vafadar, A., (2020). A review: Drilling performance and hole quality of aluminium alloys for aerospace applications. Journal of Materials Research and Technology, 9(6): 12484-12500.
  • [2] Pinar, A.M., (2013). Optimization of process parameters with minimum surface roughness in the pocket machining of AA5083 aluminum alloy via Taguchi method. Arabian Journal for Science and Engineering, 38: 705-714.
  • [3] Campbell, F.C., (2008). Elements of metallurgy and engineering alloys. ASM international, 487-508.
  • [4] Zhao, J., Deng, Y., Tang, J., Zhang, J., (2019). Influence of strain rate on hot deformation behavior and recrystallization behavior under isothermal compression of Al-Zn-Mg-Cu alloy. Journal of Alloys and Compounds, 809: 151788.
  • [5] Sun, D. et al., (2018). Hole-making processes and their impacts on the microstructure and fatigue response of aircraft alloys. The International Journal of Advanced Manufacturing Technology, 94(5): 1719-1726.
  • [6] Zhu, Z. et al., (2018). Evaluation of novel tool geometries in dry drilling aluminium 2024-T351/titanium Ti6Al4V stack. Journal of Materials Processing Technology, 259: 270-281.
  • [7] Kalidas, S., DeVor, R.E., Kapoor, S.G., (2001). Experimental investigation of the effect of drill coatings on hole quality under dry and wet drilling conditions. Surface and Coatings Technology, 148(2-3): 117-128.
  • [8] Aamir, M., Tolouei-Rad, M., Giasin, K., Vafadar, A., (2020). Machinability of Al2024, Al6061, and Al5083 alloys using multi-hole simultaneous drilling approach. Journal of Materials Research and Technology, 9(5): 10991-11002.
  • [9] Jovičević-Klug, P., Puš, G., Jovičević-Klug, M., Žužek, B., Podgornik, B., (2022). Influence of heat treatment parameters on effectiveness of deep cryogenic treatment on properties of high-speed steels. Materials Science and Engineering: A, 829: 142157.
  • [10] Molinari, A., Pellizzari, M., Gialanella, S., Straffelini, G., Stiasny, K., (2001). Effect of deep cryogenic treatment on the mechanical properties of tool steels. Journal of materials processing technology, 118(1-3): 350-355.
  • [11] Da Silva, F.J., Franco, S.D., Machado, A.R., Ezugwu, E.O., Souza Jr, A.M., (2006). Performance of cryogenically treated HSS tools. Wear, 261(5-6): 674-685.
  • [12] Adin, M.Ş., (2022). Kriyojenik ısıl işlem uygulanmış özel tasarlanmış matkap uçları ile fiber takviyeli cam-epoksi kompozitin delme performansı ve mekanik özelliklerinin incelenmesi. Doktora Tezi, Batman Üniversitesi Lisansüstü Eğitim Enstitüsü, 1-266.
  • [13] Jovičević-Klug, P., Jovičević-Klug, M., Podgornik, B., (2020). Effectiveness of deep cryogenic treatment on carbide precipitation. Journal of Materials Research and Technology, 9(6): 13014-13026.
  • [14] Jovičević-Klug, P., Tóth, L., Podgornik, B., (2022). Comparison of K340 Steel Microstructure and Mechanical Properties Using Shallow and Deep Cryogenic Treatment. Coatings, 12(9): 1296.
  • [15] Akhbarizadeh, A., Shafyei, A., Golozar, M., (2009). Effects of cryogenic treatment on wear behavior of D6 tool steel. Materials & Design, 30(8): 3259-3264.
  • [16] Gürbüz, H., Baday, Ş., (2021). Milling Inconel 718 workpiece with cryogenically treated and untreated cutting tools. The International Journal of Advanced Manufacturing Technology, 116: 3135-3148.
  • [17] Baday, Ş., Ersöz, O., (2022). Comparative investigations of cryo-treated and untreated inserts on machinability of AISI 1050 by using response surface methodology, ANOVA and Taguchi design. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 236(3): 1751-1765.
  • [18] Güney, F., Menderes, K., Gerengi, H., Kaya, E., Yıldız, M., (2022). Farklı Bekletme Süreli Derin Kriyojenik İşlemin Sementasyon Çeliğinin Korozyon Davranışına Etkisinin Araştırılması. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 9(2): 703-712.
  • [19] Kam, M., İpekçi, A., Argun, K., (2022). Experimental investigation and optimization of machining parameters of deep cryogenically treated and tempered steels in electrical discharge machining process. Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering, 236(5): 1927-1935.
  • [20] Güney, F., Menderes, K., (2022). AISI 8620 (20NiCrMo2) Çeliğinin Mekanik Özelliklerine Kriyojenik İşlemin Etkisinin İncelenmesi. İmalat Teknolojileri ve Uygulamaları, 3(2): 22-31.
  • [21] Lal, D.M., Renganarayanan, S., Kalanidhi, A., (2001). Cryogenic treatment to augment wear resistance of tool and die steels. Cryogenics, 41(3): 149-155.
  • [22] Akincioğlu, S., Gökkaya, H., Uygur, İ., (2015). A review of cryogenic treatment on cutting tools. The International Journal of Advanced Manufacturing Technology, 78(9-12): 1609-1627.
  • [23] Gill, S.S., (2012). Machining performance of cryogenically treated AISI M2 high speed steel tools. Journal of Engineering Research and Studies, 3(2): 45-49.
  • [24] Shirbhate, A., Deshpande, N., Puri, Y., (2012). Effect of cryogenic treatment on cutting torque and surface finish in drilling operation with AISI M2 high speed steel. Int. J. Mech. Eng. Rob. Res, 1(2): 50-58.
  • [25] Firouzdor, V., Nejati, E., Khomamizadeh, F., (2008). Effect of deep cryogenic treatment on wear resistance and tool life of M2 HSS drill. Journal of materials processing technology, 206(1-3): 467-472.
  • [26] Podgornik, B., Leskovšek, V., Vižintin, J., (2009). Influence of deep-cryogenic treatment on tribological properties of P/M high-speed steel. Materials and Manufacturing Processes, 24(7-8): 734-738.
  • [27] Taguchi, G., (1987). System of experimental design, quality resources, New York, USA.
  • [28] Tiwary, V.K., Arunkumar, P., Malik, V.R., (2023). Investigations on microwave-assisted welding of MEX additive manufactured parts to overcome the bed size limitation. Journal of Advanced Joining Processes, 7: 100141.
  • [29] Tiwary, V.K., Padmakumar, A., Malik, V.R., (2022). Investigations on FSW of nylon micro-particle enhanced 3D printed parts applied to a Clark-Y UAV wing. Welding International, 36(8): 474-488.
  • [30] Tiwary, V.K., Padmakumar, A., Malik, V., (2022). Adhesive bonding of similar/dissimilar three-dimensional printed parts (ABS/PLA) considering joint design, surface treatments, and adhesive types. Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science, 236(16): 8991-9002.
  • [31] Adin, M.Ş., İşcan, B., Baday, Ş., (2022). Optimization of welding parameters of AISI 431 and AISI 1020 joints joined by friction welding using taguchi method. Bilecik Şeyh Edebali Üniversitesi Fen Bilimleri Dergisi, 9(1): 453-470.
  • [32] Adin, M.Ş., İşcan, B., (2022). Optimization of process parameters of medium carbon steel joints joined by MIG welding using Taguchi method. European Mechanical Science, 6(1): 17-26.
  • [33] Ross, P.J., (1988). Taguchi technique for quality engineering. McGraw-Hill Professional, New York, USA
  • [34] Suthar, J., Teli, S., Murumkar, A., (2021). Drilling process improvement by Taguchi method. Materials Today: Proceedings, 47: 2814-2819.
  • [35] Sarikaya, M. et al., (2021). Cooling techniques to improve the machinability and sustainability of light-weight alloys: A state-of-the-art review. Journal of Manufacturing Processes, 62: 179-201.
  • [36] Markopoulos, A.P., Davim, J.P., (2017). Advanced machining processes: innovative modeling techniques. CRC Press, Taylor & Francis, 1-351.
  • [37] Giasin, K., Hodzic, A., Phadnis, V., Ayvar-Soberanis, S., (2016). Assessment of cutting forces and hole quality in drilling Al2024 aluminium alloy: experimental and finite element study. The International Journal of Advanced Manufacturing Technology, 87(5): 2041-2061.
  • [38] Aamir, M., Tolouei-Rad, M., Giasin, K., Vafadar, A., (2020). Feasibility of tool configuration and the effect of tool material, and tool geometry in multi-hole simultaneous drilling of Al2024. The International Journal of Advanced Manufacturing Technology, 111(3): 861-879.
  • [39] Aamir, M., Tolouei-Rad, M., Giasin, K., (2021). Multi-spindle drilling of Al2024 alloy and the effect of TiAlN and TiSiN-coated carbide drills for productivity improvement. The International Journal of Advanced Manufacturing Technology, 114(9): 3047-3056.
  • [40] Aamir, M., Tolouei-Rad, M., Vafadar, A., Raja, M.N.A., Giasin, K., (2020). Performance analysis of multi-spindle drilling of Al2024 with TiN and TiCN coated drills using experimental and artificial neural networks technique. Applied Sciences, 10(23): 8633.
  • [41] Santos, M.C., Machado, A.R., Sales, W.F., Barrozo, M.A., Ezugwu, E.O., (2016). Machining of aluminum alloys: a review. The International Journal of Advanced Manufacturing Technology, 86: 3067-3080.
  • [42] Ng, E., Szablewski, D., Dumitrescu, M., Elbestawi, M., Sokolowski, J., (2004). High speed face milling of a aluminium silicon alloy casting. CIRP Annals, 53(1): 69-72.
  • [43] Tash, M., Samuel, F., Mucciardi, F., Doty, H., Valtierra, S., (2006). Effect of metallurgical parameters on the machinability of heat-treated 356 and 319 aluminum alloys. Materials Science and Engineering: A, 434(1-2): 207-217.
  • [44] Fuh, K.-H., Wu, C.-F., (1995). A residual-stress model for the milling of aluminum alloy (2014-T6). Journal of Materials Processing Technology, 51(1-4): 87-105.
  • [45] Lahres, M., Müller-Hummel, P., Doerfel, O., (1997). Applicability of different hard coatings in dry milling aluminium alloys. Surface and Coatings Technology, 91(1-2): 116-121.
  • [46] Kurt, M., Bagci, E., Kaynak, Y., (2009). Application of Taguchi methods in the optimization of cutting parameters for surface finish and hole diameter accuracy in dry drilling processes. The International Journal of Advanced Manufacturing Technology, 40(5): 458-469.
  • [47] Phadke, M.S., (1995). Quality engineering using robust design. Prentice-Hill, Englewood Cliffs, NJ, USA.
  • [48] Çiçek, A., Kıvak, T., Ekici, E., (2015). Optimization of drilling parameters using Taguchi technique and response surface methodology (RSM) in drilling of AISI 304 steel with cryogenically treated HSS drills. Journal of Intelligent Manufacturing, 26(2): 295-305.
  • [49] Ross, P.J., (1996). Taguchi techniques for quality engineering: loss function, orthogonal experiments, parameter and tolerance design, 1-279, ‎ McGraw Hill, Boston, USA.
  • [50] Adin, M.Ş., (2022). Lazer kaynağı ile kaynak yapılan alüminyum alaşımlarının mekanik özelliklerinin araştırılması ve kaynak parametrelerinin taguchi ve anova yöntemleri kullanılarak optimizasyonu. Journal of Science, Technology and Engineering Research, 3(2): 50-59.
  • [51] Kumari, S., Bandhu, D., Muchhadiya, A., Abhishek, K., (2023). Recent trends in parametric influence and microstructural analysis of friction stir welding for polymer composites. Advances in Materials and Processing Technologies, 1-21.
  • [52] Murali Mohan, M., Venugopal Goud, E., Deva Kumar, M., Kumar, V., Kumar, M., “Parametric Optimization and Evaluation of Machining Performance for Aluminium-Based Hybrid Composite Using Utility-Taguchi Approach,” in Recent Advances in Smart Manufacturing and Materials: Select Proceedings of ICEM 2020, 2021: Springer, 289-300.
  • [53] Montgomery, D.C., (2017). Design and analysis of experiments, Ninth ed. John wiley & sons.
Toplam 53 adet kaynakça vardır.

Ayrıntılar

Birincil Dil İngilizce
Konular Makine Mühendisliği
Bölüm Research Article
Yazarlar

Mehmet Şükrü Adin 0000-0002-2307-9669

Yayımlanma Tarihi 20 Haziran 2023
Kabul Tarihi 9 Nisan 2023
Yayımlandığı Sayı Yıl 2023 Cilt: 7 Sayı: 2

Kaynak Göster

APA Adin, M. Ş. (2023). Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy. European Mechanical Science, 7(2), 70-81. https://doi.org/10.26701/ems.1270937
AMA Adin MŞ. Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy. EMS. Haziran 2023;7(2):70-81. doi:10.26701/ems.1270937
Chicago Adin, Mehmet Şükrü. “Performances of Cryo-Treated and Untreated Cutting Tools in Machining of AA7075 Aerospace Aluminium Alloy”. European Mechanical Science 7, sy. 2 (Haziran 2023): 70-81. https://doi.org/10.26701/ems.1270937.
EndNote Adin MŞ (01 Haziran 2023) Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy. European Mechanical Science 7 2 70–81.
IEEE M. Ş. Adin, “Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy”, EMS, c. 7, sy. 2, ss. 70–81, 2023, doi: 10.26701/ems.1270937.
ISNAD Adin, Mehmet Şükrü. “Performances of Cryo-Treated and Untreated Cutting Tools in Machining of AA7075 Aerospace Aluminium Alloy”. European Mechanical Science 7/2 (Haziran 2023), 70-81. https://doi.org/10.26701/ems.1270937.
JAMA Adin MŞ. Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy. EMS. 2023;7:70–81.
MLA Adin, Mehmet Şükrü. “Performances of Cryo-Treated and Untreated Cutting Tools in Machining of AA7075 Aerospace Aluminium Alloy”. European Mechanical Science, c. 7, sy. 2, 2023, ss. 70-81, doi:10.26701/ems.1270937.
Vancouver Adin MŞ. Performances of cryo-treated and untreated cutting tools in machining of AA7075 aerospace aluminium alloy. EMS. 2023;7(2):70-81.

Cited By

Machinability evaluation of magnesium composite using response surface methodology and nature-inspired metaheuristic algorithms
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-024-01866-3
Reciprocating dry sliding wear behaviour of BN@MXene@AA7075 composites
Journal of Composite Materials
https://doi.org/10.1177/00219983241257665
Microwave-enhanced In-Situ casting of Al-7075 Alloy: a comprehensive experimental and numerical investigation
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-024-01897-w
Experimental study on cutting force in shear thickening polishing of hardened bearing steel
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-024-01804-3
Optimization of process parameters in plasma arc cutting of commercial-grade aluminium plate
High Temperature Materials and Processes
https://doi.org/10.1515/htmp-2022-0329
Experimental analysis and optimization of machining parameters for Nitinol alloy: A Taguchi and multi-attribute decision-making approach
High Temperature Materials and Processes
https://doi.org/10.1515/htmp-2022-0324
Application of metal cored filler wire for environmental-friendly welding of low alloy steel: experimental investigation and parametric optimization
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-024-01780-8
Derin Sıfıraltı Isıl İşlemin Bimetallerin Bazı Mekanik Özelliklerine Etkisi
Fırat Üniversitesi Mühendislik Bilimleri Dergisi
https://doi.org/10.35234/fumbd.1335012
Predictive and experimental analysis of forces in die-less forming using artificial intelligence techniques
Proceedings of the Institution of Mechanical Engineers, Part E: Journal of Process Mechanical Engineering
https://doi.org/10.1177/09544089241235473
A review on the use of microslit for various applications and its fabrication
Journal of the Brazilian Society of Mechanical Sciences and Engineering
https://doi.org/10.1007/s40430-023-04638-4
Diametral error correction in turning slender workpieces: an integrated approach
The International Journal of Advanced Manufacturing Technology
https://doi.org/10.1007/s00170-023-12825-9
Optimization of hybrid Al-MMC drilling using a new RAMS-RATMI-based approach
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01628-7
Influence of cutting tool geometry when milling Nomex honeycomb structure
The International Journal of Advanced Manufacturing Technology
https://doi.org/10.1007/s00170-023-12729-8
Understand and quantify the consumers’ cognitive behavior for the appropriateness features of product aesthetics through the eye-tracking technique
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01656-3
Experimental and artificial neural network-based slurry erosion behavior evaluation of cast iron
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01618-9
Predictive optimization of surface quality, cost, and energy consumption during milling alloy 2017A: an approach integrating GA-ANN and RSM models
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01613-0
Investigation of delamination and surface roughness in end milling of glass fibre reinforced polymer composites using Fuzzy Model and Grey wolf Optimizer
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01576-2
Machining performance evaluation and optimization for graphene oxide/CF-based composite using utility-taguchi approach
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01563-7
Evaluation of surface roughness of novel Al-based MMCs using Box-Cox transformation
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01561-9
Performance evaluation of machining efficiency using graphite powder-based EDM: for aerospace application
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01558-4
Sustainable shape formation of multifunctional carbon fiber-reinforced polymer composites: A study on recent advancements
Mechanics of Advanced Materials and Structures
https://doi.org/10.1080/15376494.2023.2259901
Machining aerospace aluminium alloy with cryo-treated and untreated HSS cutting tools
Advances in Materials and Processing Technologies
https://doi.org/10.1080/2374068X.2023.2273035
Towards green machining: wear analysis of a novel eco-friendly cooling strategy for Inconel 718
The International Journal of Advanced Manufacturing Technology
https://doi.org/10.1007/s00170-023-12207-1
Sustainable New Technology for the Improvement of Metallic Materials for Future Energy Applications
Coatings
https://doi.org/10.3390/coatings13111822
Predicting the thermal performance of screen mesh wick heat pipe with alumina nanofluids using response surface methodology
International Journal on Interactive Design and Manufacturing (IJIDeM)
https://doi.org/10.1007/s12008-023-01473-8
Experimental Assessment of Hole Quality and Tool Condition in the Machining of an Aerospace Alloy
Machines
https://doi.org/10.3390/machines11070726
 Kapak Resmi İndir

Dergi TR Dizin'de Taranmaktadır.

Flag Counter